• R820FA
  • R820FA
  • R820FA
  • R820FA
  • R820FA
R820FA
R820FA
R820FA
R820FA
R820FA
+

R820FA

Skype/ Wechat:

Still deciding? Please contact us immediately!

Current product category

R820FA


Still deciding? Please contact us immediately!

Current product category

Key words

  • Product Description
  • Compatibility:

    2.4GHz Spread Spectrum FASST Compatible Receiver is designed to use with FUTABA FASST 2.4GHz transmitters, such as TM7, TM8, TM10, TM14 or T6EX-2.4G, 7C-2.4G, 8FG, 10CG, 12FG,14SG,18MZ

    Specifications:

    Operating Current: 50mA max
    Operating Voltage: 3.6 ~8.4V
    Latency: S.BUS mode:14mS @ FASST multi-channel mode, 16mS @ FASST 7ch mode
    CPPM mode: 21mS @ FASST multi-channel mode, 24mS @ FASST 7ch mode
    Sensitivity: about -90dBm
    Weight: about 2g
    Size: L*W*H=30mm*14mm*3mm
    Output mode: S.BUS or CPPM can be selected

    Setup

    Bind procedure:

    • Turn on the FASST transmitter
    • Connect the battery to the receiver while pressing receiver’s F/S button.
    • The Dual-color LED’s continuous will cycle through the following:
      • Red LED light (searching radio signal)
      • Green LED light (acquired the radio signal)
      • Red LED off (bind ok)
      • Green LED flashes 10 times (ID store in memory)
      • Green LED lights solid (normally operation)

    Fail-safe setting:

    TX-failsafe feature: This method is to set failsafe on the FASST transmitter (works on channel 3 only under FASST 7ch mode or on multiple-channels under FASST multi-channel mode) while the receiver is working on, just like the FUTABA receivers.

    Nore:

    We highly recommend you set failsafe feature while flying your models. An example of a useful Failsafe setting would be to shut down the model’s throttle, so that it does not fly or drive away uncontrolled.

    Output mode setting:

    If your receiver has been linked with your transmitter, please power off your transmitter. When your receiver’s LED light red, push down and hold the button on your receiver for more than 6 seconds and not more than 10 seconds, release the button to see the green led flash, push down the button again right now, receiver get back to light red. Now the MODE status has changed between S.BUS output mode and CPPM(continuous PPM signal on one wire) mode. When green led flash low indicate S.BUS mode to CPPM mode, and green led flash fast indicate CPPM mode to S.BUS mode. And power on the receiver again to take new feature effect.
    Do not connect any servo directly to the RX, it maybe get abnormal action or get hot.

    LED status indicated under normal working status:

    RED LED GREEN LED Status
    on off No signal searched
    on solid Signal is very good
    on flash Signal is not very good
    on off-flash Signal is weak

     

    manual

    2.4GHz Spread Spectrum (FASST COMPATIBLE)

    Receiver Instruction Manual(MINI FASST RX)

    (LBT compatible)

    Compatibility:

    2.4GHz Spread Spectrum FASST Compatible Receiver is designed to use with FUTABA FASST 2.4GHz transmitters, such as TM7, TM8, TM10, TM14 or T6EX-2.4G, 7C-2.4G, 8FG, 10CG, 12FG,14SG,18MZ

     

    Specifications:

    Operating Current: 50mA max

    Operating Voltage: 3.6 ~8.4V

    Latency: S.BUS mode:14mS @ FASST multi-channel mode, 16mS @ FASST 7ch mode

    CPPM mode: 21mS @ FASST multi-channel mode, 24mS @ FASST 7ch mode

    Sensitivity: about -90dBm

    Weight: about 2g

    SIZE: L*W*H=30mm*14mm*3mm

    Output mode: S.BUS or CPPM can be selected

     

    Setup:

    Bind procedure:

    • Turn on the FASST transmitter
    • Connect the battery to the receiver while pressing receiver’s F/S button.
    • The Dual-color LED’s continuous will cycle through the following:
      • Red LED light (searching radio signal)
      • Green LED light (acquired the radio signal)
      • Red LED off (bind ok)
      • Green LED flashes 10 times (ID store in memory)
      • Green LED lights solid (normally operation)

     

    Fail-safe setting:

    TX-failsafe feature: This method is to set failsafe on the FASST transmitter (works on channel 3 only under FASST 7ch mode or on multiple-channels under FASST multi-channel mode) while the receiver is working on, just like the FUTABA receivers.

     

    Note:   We highly recommend you set failsafe feature while flying your models. An example of a useful Failsafe setting would be to shut down the model’s throttle, so that it does not fly or drive away uncontrolled.

     

    Output  mode setting:

    If your receiver has been linked with your transmitter, please power off your transmitter. When your receiver’s LED light red, push down and hold the button on your receiver for more than 6 seconds and not more than 10 seconds, release the button to see the green led flash, push down the button again right now, receiver get back to light red. Now the MODE status has changed between S.BUS output mode and CPPM(continuous PPM signal on one wire) mode. When green led flash low indicate S.BUS mode to CPPM mode, and green led flash fast indicate CPPM mode to S.BUS mode. And power on the receiver again to take new feature effect.

           Do not connect any servo directly to the RX, it maybe get abnormal action or get hot.

     

    LED status indicated under normal working status:

    RED LED

    GREEN LED

    Status

    on

    off

    No signal searched

    off

    solid

    Signal is very good

    off

    flash

    Signal is not very good

    off

    off-flash

    Signal is weak

Inquire Now

Note: Please leave your email address, our professionals will contact you as soon as possible!