CT8Z+CR8D
Still deciding? Please contact us immediately!
Current product category
CT8Z+CR8D
Still deciding? Please contact us immediately!
Current product category
Key words
- Product Description
-
Brief Instruction
Corona 2.4GHz DIY Radio Control System
Thank you for purchasing our Corona 2.4Ghz DIY RF transmitter module & receiver. In order to fully utilize the performance potential of this system, we suggest you first read the manual.
Using the Corona 2.4GHz DIY system
Corona 2.4GHz DIY system including the Components below:
Transmitting board,Extend board,3 color line,4 color line, Antenna connector,Transmitter antenna,Instruction Manual,Paper marker, screws,nuts, washers.
Corona 2.4GHz DIY system will work with Corona’s receiver of CR2D, CR3D, CR4D, CR6D and CR8D
- The Corona 2.4GHz DIY transmitter module and receiver are designed to completely eliminate radio interference and glitches which have troubled model hobbyists for years. The software designed exclusively for the transmitting module and receiver instantly locates and assigns safe and protected channels. Other flyers in the area can not create interference that normally would corrupt transmitter signals. The Corona 2.4GHz adheres strictly to Direct Sequence Spread Spectrum (DSSS) communication standards by constantly switching across a wide band of frequencies. Combining Corona’s software with FHSS we have designed a transmitter and receiver capable of providing modelers the highest performing radio system available.
Features of Corona 2.4GHz DIY transmitting module and receiver
The new lightweight, advanced technology unit has the following features:
1. Extended operating range 1.5 km range, which has been tested in a real flying environment.
2. A 3dbi gain transmitting antenna ensures the wave lengths are evenly distributed throughout the transmitting horizon ensuring the stable signal.
3. One-key user friendly setup mode.
4. Perfect receiver antennas guarantee the plane receives the signal regardless of the maneuver or attitude.
5. The unique receiver design makes the Corona module easy to install and ensures reliability.
- Corona's advanced needle design ensures the lightest possible receiver
Installation the 2.4GHz DIY transmitting module
- Open the transmitter,find out the Battery power supply line,PPM signal line,and the GND.You can find out Battery power supply line just behind the power switch use a voltage meter and find out the PPM signal with an oscillograph.
- Take the order, solder the PPM signal line,Battery power supply line,GND to the DIY transmitting module(left up corner of the Figure1 )
Figure 1
- Drill four holes on the transmitter as the paper marker guided,two holes on diagonal is designed for screw installation,the other two for dual color LED and the button.Put the paper marker on the outside of transmitter where the internal space is free to fix the extend board(Figure2) and Drill the four holes.
Figure 2
- Solder the 4 color lines between transmitting board and the extend board take the order guided by the screen painting.
- Solder the antenna connector at the port ANT on transmitting board.
- Drill a hole for antenna connector at the space free on the transmitter.The diameter is 7mm is suitable.Fix the antenna connector like Figure 3.
Figure 3
- Fix the transmitter antenna on the connector .Turn the transmitter power on and check the power indicator LED of DIY extend board,the LED is normally light red.
Transmitting and receiving communication setup
Installation of receivers
As the wave length of 2.4GHz is shorter, its ability to go around obstacles is weaker than receivers whose frequency is below the 100MHz .Therefore, when you install the antenna, you must avoid objects with high conductivity such as; metal parts, servos, ESC’s, battery, wires, and carbon fiber structures. If possible put the end of the antenna outside of the fuselage.
Receiver and Transmitter Setup Instructions
- Turn the transmitter on and adjust your transmitter to PPM mode and then turn the transmitter off.
- Press the programming button on the extend board (CT8Z) while turning the transmitter on, then release the button (Attention: Don’t keep holding the button down over 3 seconds,or its ID will change randomly). The LED on Module will flash between red and green indicating the transmitter is ready to bind with the receiver.
- Press and hold the button on the receiver(CR8D) and power the receiver on. The LED on the receiver will flash twice, indicating the receiver have recognized the transmitter. Turn off the transmitter and receiver.
- Power on the receiver(s) without pressing any button, then power up the transmitter also without pressing button, the LED on the transmitter light red. The RF-link will normally connect in 5~10 seconds between transmitter and the receiver(s).If linked the LED on the receiver(s) will light red without any flash indicating the receiver(s) is operating properly. If the LED flashes intermittently or does not light at all. Repeat this step until link is connected properly.
- After setup, give power to the transmitter firstly and it will transfer singnal , about 5 seconds later give power to the receiver to check the red led light steadily if all servos are under controlling it means it is ready to fly .
We hope you enjoy your new 2.4 Ghz receiver and transmitter modules. They have been designed and produced using the highest quality control measures available. If you have any questions please do not hesitate to contact us or visit our website.
Range checking
This is necessary for safe operation and must be incorporated into your setup and pre-flight operations.
Failsafe setting for receiver
Within in 10 seconds after the receiver link to the transmitter adjust the switch (or button) of transmitter and press the button of receiver, the LED on receiver will flash 2-3 seconds then keep lit that means the failsafe setting finished .
Caution: must be exercised when using the unit in an environment that full of mental fences, concrete buildings, or rows of trees. In this environment you may experience unexpected radio wave multipath interference.
You must conduct a range check as follows (Note this is done with the receiver out of the plane):
1. Place the receivers at least two feet (60cm) above non-metal contaminated ground; for example a wooden bench.
2. Fix the antenna of receiver horizontally. Don’t let antenna touch the ground.
3. Connect a servo to channel one.
4. Place the antenna of the transmitter in a vertical position.
5. Turn on the transmitter and receiver and walk away from receiver while moving the stick which controls the channel one. Ask someone to check the distance at which the servo doesn’t responce.
Attention: Controlling distance is greatly related to the transmitter’s power energy. Please use freshly charged battery packs when you conduct the test. Controlling distance is affected by environment too. Please test it in the open away from any obstacles. The controlling distance in the air is greater than that on the ground. Our controlling range is based on a conservative ground test.
Corona 2.4GHz Radio System Nomenclature
Transmitter:
C T 8 Z
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |---------------------Z: DIY
| | |-----------------------------8:8 channel
| |-------------------------------------T: Transmitter
|-----------------------------------------------C: Corona
Receiver:
C R 8 D L
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |-----L: long antenna / S:short antenna
| | | |-------------F: FHSS /D: DSSS
| | |----------------------8:8 channel
| |------------------------------R: receiver
|----------------------------------------C: Corona
Specification:
Specification for the transmitter module CT8Z:
min
typ
max
remark
Operating voltage range
8V
10V
13v
Rely on the transmitter
Operating current
100mA
Resolution
10bit
Specification for the Receiver CR8DL:
min
typ
max
remark
Operating voltage range
4.8V
5.0V
6V
Operatint current
30mA
Specified range
1.5km
Resolution
10bit
Latency
22ms
Sensitivity
-100dbm
Inquire Now
Note: Please leave your email address, our professionals will contact you as soon as possible!